knobs
Page 1 of 1
knobs
Who has the most knobs for sale? New or retro. I need two sets . Need a site where i can email a question or two.
And someone who sell transformers. Ichecked some places but no luck.
And someone who sell transformers. Ichecked some places but no luck.

denver- Member
- Number of posts : 381
Age : 60
Registration date : 2010-01-18
Re: knobs
I have a couple of knobs for sale.
Knowing what radio you will use them on is kind of a help in this case.
Original knobs might cost more. Repro knobs like from Larry Bordonaro may be the best option. There are other repro-ers out there Google is your friend.
"Need a site where i can email a question or two."
You can post questions right here
. Or the ARF or Philco Phorum, or one of the other fine vintage radio sites out there..
Again, what set do you need a transformer for? You can have a custom wound trans, (around $80 to $100), a generic replacement (AES or Radio Daze, etc.) or find a good original used one.
There are more than one site for parts like that. Some might have one, but not the other. Playthings of the past might have your trans, might not. Rewind your old trans perhaps? Heyboer rewinds and custom winds.
Please include a little more info with your post, so we can all zero in on exactly what you need. Good luck.
Gary.
Knowing what radio you will use them on is kind of a help in this case.
Original knobs might cost more. Repro knobs like from Larry Bordonaro may be the best option. There are other repro-ers out there Google is your friend.
"Need a site where i can email a question or two."
You can post questions right here

Again, what set do you need a transformer for? You can have a custom wound trans, (around $80 to $100), a generic replacement (AES or Radio Daze, etc.) or find a good original used one.
There are more than one site for parts like that. Some might have one, but not the other. Playthings of the past might have your trans, might not. Rewind your old trans perhaps? Heyboer rewinds and custom winds.
Please include a little more info with your post, so we can all zero in on exactly what you need. Good luck.
Gary.
GaryRabbitt- Member
- Number of posts : 95
Registration date : 2008-07-04
Re: knobs
It is a crosley model o3cq chassi 95 . Tried to find a pic of this set but no luck. There is a schematic for it at nosalgia air .A few other sets has same chassi. Maybe i can find a pic of one of the other sets to compare knobs. Mine looks like they melted.
denver- Member
- Number of posts : 381
Age : 60
Registration date : 2010-01-18
Re: knobs
It has two piece knobs one shaft through other.
Back knob selection front knob for off on volume.
Or tuning dial.
Back knob selection front knob for off on volume.
Or tuning dial.
denver- Member
- Number of posts : 381
Age : 60
Registration date : 2010-01-18
Re: knobs
http://www.flickr.com/mr38/3975037785/
denver- Member
- Number of posts : 381
Age : 60
Registration date : 2010-01-18
Re: knobs
Finally found a pic of the knobs. What i need and the piece
on the left around the push buttons.
on the left around the push buttons.
denver- Member
- Number of posts : 381
Age : 60
Registration date : 2010-01-18
Re: knobs
I don't have that bezel, you may want to check with Radiopup on the ARF board. I have seen them at radio swaps before.
Please try to keep posts in one thread, about the same model. It will help reduce the confusion.
Please try to keep posts in one thread, about the same model. It will help reduce the confusion.
GaryRabbitt- Member
- Number of posts : 95
Registration date : 2008-07-04
Re: knobs
Thanks and roger that.

denver- Member
- Number of posts : 381
Age : 60
Registration date : 2010-01-18
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum
|
|